Section: Linux Programmer's Manual (2)
Return to Main Contents
splice - splice data to/from a pipe
#define _GNU_SOURCE /* See feature_test_macros(7) */
ssize_t splice(int fd_in, loff_t *off_in, int fd_out,
loff_t *off_out, size_t len, unsigned int flags);
moves data between two file descriptors
without copying between kernel address space and user address space.
It transfers up to
bytes of data from the file descriptor
to the file descriptor
where one of the file descriptors must refer to a pipe.
The following semantics apply for
refers to a pipe, then
must be NULL.
does not refer to a pipe and
is NULL, then bytes are read from
starting from the file offset,
and the file offset is adjusted appropriately.
does not refer to a pipe and
is not NULL, then
must point to a buffer which specifies the starting
offset from which bytes will be read from
in this case, the file offset of
is not changed.
Analogous statements apply for
argument is a bit mask that is composed by ORing together
zero or more of the following values:
Attempt to move pages instead of copying.
This is only a hint to the kernel:
pages may still be copied if the kernel cannot move the
pages from the pipe, or if
the pipe buffers don't refer to full pages.
The initial implementation of this flag was buggy:
therefore starting in Linux 2.6.21 it is a no-op
(but is still permitted in a
in the future, a correct implementation may be restored.
Do not block on I/O.
This makes the splice pipe operations nonblocking, but
may nevertheless block because the file descriptors that
are spliced to/from may block (unless they have the
More data will be coming in a subsequent splice.
This is a helpful hint when
refers to a socket (see also the description of
and the description of
Upon successful completion,
returns the number of bytes
spliced to or from the pipe.
A return value of 0 means end of input.
refers to a pipe, then this means that there was no data to transfer,
and it would not make sense to block because there are no writers
connected to the write end of the pipe.
returns -1 and
is set to indicate the error.
was specified in
and the operation would block.
One or both file descriptors are not valid,
or do not have proper read-write mode.
The target filesystem doesn't support splicing.
The target file is opened in append mode.
Neither of the file descriptors refers to a pipe.
An offset was given for nonseekable device (e.g., a pipe).
refer to the same pipe.
Out of memory.
was not NULL, but the corresponding file descriptor refers to a pipe.
system call first appeared in Linux 2.6.17;
library support was added to glibc in version 2.5.
This system call is Linux-specific.
The three system calls
provide user-space programs with full control over an arbitrary
kernel buffer, implemented within the kernel using the same type
of buffer that is used for a pipe.
In overview, these system calls perform the following tasks:
moves data from the buffer to an arbitrary file descriptor, or vice versa,
or from one buffer to another.
"copies" the data from one buffer to another.
"copies" data from user space into the buffer.
Though we talk of copying, actual copies are generally avoided.
The kernel does this by implementing a pipe buffer as a set
of reference-counted pointers to pages of kernel memory.
The kernel creates "copies" of pages in a buffer by creating new
pointers (for the output buffer) referring to the pages,
and increasing the reference counts for the pages:
only pointers are copied, not the pages of the buffer.
In Linux 2.6.30 and earlier,
exactly one of
was required to be a pipe.
Since Linux 2.6.31,
both arguments may refer to pipes.
This page is part of release 4.15 of the Linux
A description of the project,
information about reporting bugs,
and the latest version of this page,
can be found at
- RETURN VALUE
- CONFORMING TO
- SEE ALSO
This document was created by
using the manual pages.
Time: 16:41:11 GMT, September 25, 2018